Feb 262015
 

The brakes have been connected and plumbed in for quite a while now. The system only had to be filled with brake fluid and bled, so I had assumed the brakes were essentially complete and wouldn’t be noteworthy. I should have known by now that was almost certainly going to be wildly optimistic …

I had dithered on the type of fluid to use, glycol base or silicone, changing my mind almost on a daily basis before finally making the decision to stick with glycol based DOT4 fluid. The ‘this is absolutely my final decision’ was subsequently reversed to silicone following an interesting article on the subject sent to me by Chris Jackson, whose restoration is being covered in the E-type Magazine.
DOT5 Silicone Brake Fluid

The debate regarding DOT4 (Glycol) verses DOT5 (Silicone) seems to be quite polar in nature. A bit like Marmite – people are either for it or hate it and never the two shall meet! At the time I’d just been working through fixing leaks in the cooling system. Reports of leaks from weeping hoses and splitting repro reservoir bottles are all too common. The thought of brake fluid leaking onto the paint work and remaining undetected paid a significant part in opting for silicone.

However some have raised concerns that silicone fluid might cause rubber seals to swell. Possibly but the composition of the rubber seals has changed over time, with natural rubber no longer used. Modern rubber should now be compatible with all types of fluid.


Automec DOT5 Silicone Fluid

The manufacturer’s blurb suggests silicone fluid is a ‘fill and forget’ solution but I think this is a little wide of the mark as water will find its way into the system. As it doesn’t mix with the brake fluid, it would then pool and cause local corrosion so I’m still planning to replace the silicone fluid periodically, although less frequently than would be the case for DOT fluids.

Apart from the additional expense, the down side of silicone is that, when it is agitated, it has a tendency to absorb tiny air bubbles that are not visible to the eye. This can cause a spongy pedal as the bubbles compress under braking. The simple solution is to leave the fluid to settle overnight before bleeding the system, although that would be more problematic if it ever had to be refilled on a trip.

All the compression joints were checked and tightened. Now the front calipers were bolted to the uprights, sufficient torque could be applied to the bolts clamping the two caliper halves together. Correct torque settings are not published but a brake refurbishing company recommended to torque the 7/16″ diameter bolts to 70 lb-ft and the 3/8″ diameter bolts to 40 lb-ft. I’ll need to keep an eye out for any initial issues.

Remote rear bleed kit


Stevson & Fosseway kits

Another of Chris’ suggestions was to fit one of Fosseway Performance’s remote bleed kits. The standard bleed valves are hard to reach at the best of times, so moving them to a more accessible position on the IRS cage is quite a popular modification. In fact I’d already fitted a similar kit sourced from Stevson Motors prior to installing the IRS unit.

My kit was definitely more agricultural than engineered so I had been a little disappointed when it arrived. The mounting brackets were just pieces of brass sheet that looked as though they had been hand drilled and then bent in a vice.

Still their function is fairly basic and the aesthetics is not a great issue, being tucked up underneath the car, so I had fitted the Stevson kit. It was only later, when I was working underneath the car to re-fit the handbrake cable, did its design start to irk me. My patience was wearing thin after catching the sharp corner of the brass bracket for the umpteenth time.

The revisiting of the handbrake was because I’d routed the cable incorrectly. It should pass through an eyelet on the inside of the transmission tunnel, with a rubber grommet protecting the cable. The cable was too stiff to re-route in situ by disconnecting the cable from the handbrake mechanism. So the entire cable had to be removed.

Re-routing couldn’t be achieved by just disconnecting at compensator linkage Correct routing of cable through grommet in transmission tunnel eyelet

The final straw came when I found that the seat for one of the bleed valves had been machined too far. So the coned face at the end of the valve could never make contact with the seat, let alone form a seal. Longer valves are available … but not in the course thread used in the kit. There was no alternative – it had to be replaced.

I’m sure Stevsons would have rectified the problem but I now had the opportunity of fitting a better quality of kit. An order was placed and the Fosseway kit arrived the next day! The main difficulty was, with the IRS now in place, access was severely limited. The front pair of springs and dampers had to be removed to access the calipers.

Forward rear springs removed for access The Fosseway kit has better banjo attachments Fosseway kit uses sprung bleed valves

The Fosseway kit uses a banjo attachment at the calpiers which is a neater solution and much easier to fit, as it doesn’t require the flexible pipe to rotate when tightening it into the caliper. The other difference is the style of bleed valve used, sprung valves rather than standard solid valves. The sprung valves help with bleeding as the spring stops air entering the system between pumps of the brake pedal. In the end, replacing the remote bleed kit was easier than I had thought and only took an hour and a half.

Brake Bleeding Woes!
This was another task that proved far more troublesome than I had expected. Most methods of bleeding require the help of an assistant. The exception to this is vacuum pumps, such as the Mityvac, which can be operated single-handed. The vacuum is applied to the bleed valve to draw the fluid through the system so both the vacuum and bleed valve can be controlled from one location.


Mityvac vacuum bleeding tool

It was for this reason I purchased a Mityvac pump to replace my old Eezibleed tool. The Eezibleed pressurises the reservoir to push fluid through the system but still requires two people to operate. So doesn’t really offer anything over the traditional method of pumping the brake pedal.

The correct bleeding sequence according to the service manual is the near-side followed by the off-side, starting with the rears and finally moving to the front brakes. The reservoir bottles were filled, the RH reservoir feeding the front brakes and the LH reservoir the rears … let the bleeding begin!

After about 1/2 hour of trying with the Mityvac, absolutely nothing had come out of either of the rear valves. Time for plan B – the Eezibleed was rigged up to the reservoir. All this achieved was pressurising the bottle to what looked like bursting point and spraying fluid everywhere from around the cap. Thank goodness I’d gone for silicone fluid! Still nothing was coming out at the rear calipers.

Plan C! The traditional approach – the good old brake pedal and a patient helper! The resistance started to build after 20-30 pumps of the brake pedal. However this would dissipate after about 30 seconds. Frustratingly there was still no fluid coming from the rears. I suspect pumping the pedal was only pushing fluid into the front circuit and the resistance felt at the pedal was due to the air in the pipe being compressed. Once the pumping stopped the air pressure would force the fluid back into the reservoir.

Stumped, I decided to search the web to find out if there was a specific technique or trick that might help. At least I found out that I certainly wasn’t alone in having trouble bleeding the rear brakes, especially filling a dry system. One tip was to try bleeding the brakes with the engine running as the servo would be boosted by the vacuum. Still no joy!

Another suggestion was to first check the operation of the valve located in the output port of the servo cylinder. Once it had been confirmed fluid was coming out of the servo cylinder, simply loosen the rear bleed valves in turn, allowing the system to bleed naturally, under gravity. Note: the sprung valves need pressure to compress the spring to allow fluid out and so had to be removed for this method

The height of the reservoir above the remainder of the system provides a sufficient head of fluid to allow gravity to do the work for you. Whether the removal and inspection of the cylinder valve had fixed the restriction I’m not sure, but fluid was now coming out of both rear bleed valves.

Success was short lived …. when the brake pedal was depressed, fluid leaked out of the three way union mounted on the IRS cage. The problem was found to be the new flexible Goodridge brake pipe. Although sold as a direct replacement for the E-Type, the rear attachment was too short. It was a similar problem to the remote bleed kit – the attachment could never make contact with the seat and therefore create a seal.

Short end of Goodridge brake hose was too short! The additional mechanical brake light switch

Several days and a new hose later, the system was finally bled. At the same time the last few braking tasks were completed: the brake pedal was much higher than the accelerator pedal and the mechanical brake light switch was fitted.

The height of the pedal is set by adjusting a ‘stop’ screw in the pedal housing, which was set to remove any free travel in the brake pedal. Unfortunately the clutch pedal is too high as well but this doesn’t have any adjustability. Other owners have had the same problem, caused by the push rod being 1/2″ too long on the replacement master cylinders. Another job to the list!

Jan 132015
 

Jaguar made several changes to the clutch slave cylinder during the production of the E-Type which appear to have caused a fair amount of confusion amongst owners, myself included.

The slave cylinder details from the Jaguar literature are:

  • S1 to engine 7E4606 – short 80mm adjustable cylinder (part C21470)
  • S1 from engine 7E4607 – 95mm hydrostatic self-adjusting cylinder (part C24145)
  • S1 from engine 7E18356 (7E55558 for 2+2) – reverted to adjustable cylinder (part C29801)

The difference being the adjustable cylinders require a return spring and bracket to pull the fork back, so the piston is at the mid-point. The hydrostatic, self-adjusting cylinders must not have the return spring fitted. Either type can be fitted to any of the range, so you just need to know which type is fitted to determine whether to fit a return spring.

As a result, the length of the slave cylinder is often used to differentiate between the two types. A 95mm unit was supplied when I ordered a replacement C29801 cylinder and the suppliers assured me it was correct.

I made the assumption, from all the forum discussions on the subject, that I must have a hydrostatic unit and therefore didn’t include the return spring when it was fitted it to the transmission, prior to installing the engine.

It wasn’t until another S2 owner who was going through the same issue was able to confirm the 2nd version of the non-hydrostatic cylinders was 95mm, not 80mm, with the original Lockheed part having markings 3232 648C. This matched the markings on my replacement cylinder and also on the one that had been removed during the dismantling, which was fitted with a spring.

My conclusion was that the return spring will need to be fitted after all. Another recommendation was to replace the mounting stud by 5/8″ UNC x 1″ socket head bolts. This will make later removal easier as access is severely restricted.

So another task to add to the ‘To Do’ list!

Brake caliper rebuild

 Brakes, Rolling Chassis  Comments Off on Brake caliper rebuild
Jun 242013
 

The components for the front calipers - including the small circular seals between the two halvesCaliper rebuild kits are readily available from many of the usual suppliers and contain the square sectioned seals which sit in recesses in the caliper piston bores and the outer dust shields.

The dust shields are similar to a expandable bellow with the ends sitting in a recesses in the piston bore and piston. This enables the rubber shield to stop ingress of foreign particles for the full travel of the pistons.

The kits however do not contain the small square sectioned ‘O’ rings that seal the two halves of the caliper.

I think the reason being that the manufacturer provides the following warning:

Girling “split” calipers should not be separated for any reason. They were not designed for separation and reassembly and proper torque specifications are not known, other than the inner and outer bolts are torqued differently.

It seems odd for the manufacturer to give the reason that the torque specifications are not known for their own product! I can understand their wish in avoiding customers trying to split the calipers in case they are not sealed correctly and the likely consequences. Again, being of a cynical nature, I suspect this has as much to do with fear of litigation.

However, when I contacted a caliper reconditioning firm, they suggested that as long as new seals are used and the bolts are sufficiently torqued there shouldn’t be a problem. Leaks were more likely to occur elsewhere. Although I will keep an eye on the calipers once in service … just in case.

Their recommendation was to torque the 7/16″ diameter bolts to 70 lb-ft and the 3/8″ diameter bolts to 40 lb-ft. Also to work from the outside in and alternating sides each time, ie torque the outer bolt on one side then the outer bolt on the other, followed by the inner bolt next to the first outer bolt and finally the remaining inner bolt.

The front calipers have internal passageways to enable fluid to pass between the two halvesThe photo to the left shows the passageways for the brake fluid from the face where the two caliper halves join (the tip of the screwdriver is just about visible at the top of the upper piston bore). A corresponding passageway exists from the face of the other caliper joint and a small channel links the two piston bores. Thus providing the free flow of fluid between all the pistons in both halves of the caliper.

The rebuild is very straight forward. The bores and seal recesses were given a coating of Castrol Red Rubber Brake grease before the bore seal and outer dust rubber shield were fitted.

Grease was also applied to the cylinders before pressing home. The main point is to ensure the pistons were pushed in squarely to avoid damaging the seals. The outer lip of the dust shield pops into place as the piston is inserted.

Piston bore greased and seal inserted Dusty shield inserted before fitting piston

The piston bore and seal recess were covered with Girling Red Rubber grease before the seal was inserted into the recess

The rubber dust shields are insered into their groove in the caliper before pressing in the piston

Two smaller pistons & combined dust shield Greased pistons before pressing home

The front is a 3-pot caliper so one half has two smaller pistons with a combined dust shield

The pistons are also given a generous covering of rubber grease to ease fitting

Finally the two small seals between the caliper halves were greased and inserted into their recesses and the caliper bolts tightened to the torque setting above.

A square section 'O' ring sits in a recess  and provides the necessary seal between the two halves of the front caliper

Completed front and rear main calipers

The main difference between the front and rear calipers is the rears employ an external pipe for the fluid to passed between the two halves and therefore there isn’t the need for the small seals.

Jun 182013
 

My initial plans were to upgrade the brakes to vented discs with calipers from either Zeus or Coopercraft. By all accounts deficiencies with the original S1 brakes were addressed for the S2 cars so I’ve had a change of heart and will be fitting the original braking system for now. I’ll see how it goes and decide on any changes once I’ve driven it for a while.

All the calipers were sporting many years worth of brake dust, dirt and grease and were to be stripped back, cleaned and rebuilt. The rears were worse but once liberated from the IRS unit they were fairly easy to dismantle.

The rear calipers have the additional handbrake mechanisms attached

Rear caliper with external hydraulic pipe connecting the two halves

The handbrake ratchet mechanism and retraction fork

The handbrake mechanism was simply removed from top of the rear calipers by knocking back the lock tabs and removing the two retaining bolts. The other differences between the front and rear calipers is that the fronts have three pistons compared with two at the rear and the rears have and external hydraulic pipe connecting the two halves.

At the start I was somewhat bemused how one half of the front caliper worked as it didn’t appear to have any hydraulic feed. Obviously there must be an internal passage to transfer the brake fluid but I couldn’t see how the clamping force alone would create the necessary seal between the two halves of the caliper.

All became clear once it was split in half. In the middle of both clamping faces was a channel to the rear of the piston chamber thus providing a path for the brake fluid to flow between the two halves. Machined recesses contained rubber washers which would be compressed to create the required seal.

Unfortunately I’d not documented the rebuild of the calipers as it was done a number of years ago and they had been stored ever since. To my dismay, when I dug them out again, the zinc plating had already started to corrode …. and that was after storing them indoors!

The zinc coating on the refurbished front calipers had already corroded before they were even installed!

The worst corrosion areas were at the joint - I suspect it was a combination of poor plating and a pitted surface

It was probably due to poor plating but they’d certainly look quite shabby very quickly if they were fitted to the car and exposed to the elements.

The calipers would have been cadmium plated which isn’t an option nowadays due to the toxic chemicals involved. I’m relaxed over deviating from originality, especially for practicality reasons, and decided to strip them down again and paint them rather than re-plating. So it was another case of one step forward and two back!

The problem with the plating was limited to the cast iron components so only the main calipers and handbrake caliper arms will be painted. The handbrake ratchet mechanism will be left as passivated zinc.

The pistons were forced out in stages using an air foot pumpThe easiest method of extracting the pistons was to insert a bleed nipple into the hydraulic feed and use a foot pump to force the pistons out.

It’s a good idea to place a piece of wood between the pistons to limit their travel. The pistons can be pushed out in stages be reducing the thickness of wood each time. This enables all of the pistons to be pushed out rather than one popping out and the rest staying put.

It was also necessary to separate the handbrake caliper arm from the ratchet mechanism by removing the split pin and pressing out retaining pivot pin. The internal spring could then be removed more easily.

Handbrake ratchet mechanism and brake pad arms

Removing the handbrake mechanism cover reveals the spring which needed to be detached to remove the handbrake caliper arm.

The calipers were first soaked in a hot degreaser and then the joint faces and piston bores masked ready for painting. The paint kit ordered from Brake Caliper Specialists was a 300ml two pack paint (200ml paint & 100ml hardener) specifically designed for calipers, which was sufficient for all four main calipers and the handbrake caliper arms. Hopefully the 2 pack paint should prove more durable than other VHT paints.

A clothes rack provided an ideal hanging frame for the parts to be painted

All that remains is the caliper rebuilding ….

May 192013
 

While researching the best piping to use for the hydraulics, I’d found out that copper piping is banned in many countries as it is susceptible to work hardening over time. I thought it wise to switch to Cunifer pipes as it is a safety issue, even though I had already purchased a copper pipe kit from Automec.

In the end I took the cautious approach to all the braking system and planned to have the master cylinder and servo units professionally renovated. The main reason being an inspection of the master cylinder had revealed some pitting and I wasn’t confident it would be possible to get a good seal without it being re-sleeved.

Also the fixing studs on the servo unit were all at odd angles so something was amiss. Opening up the servo uncovered a bodged weld ‘repair’ to one of the studs. The servo casing looked as if it had been fractured around the stud and so would need replacing. The units were sent off to J & L Spares to be repaired. However the cost of repairing the master cylinder was more than the cost of a new one so I opted for the latter.

Servo Mounting Studs Bodged repair weld Renovated Servo

The mounting studs for the brake servo were all at odd angles, suggesting all was not well

One of the studs appears to have been bent resulting in a fracture around the stud, whic had been poorly 'repaired'

A renovated servo unit from J & L Spares

Apart from a basic understanding, I’d never really paid much attention to the detailed workings of servo assisted brake systems. So it was out with the Jaguar service manuals to get a better understanding of how the vacuum boost is controlled. It should help if troubleshooting is required later on, especially as I will be tapping into the vacuum circuit for the EDIS Megajolt control module.

It’s actually quite simple. A reservoir tank stores a ‘vacuum’ by being connected to the inlet manifold, which is at a lower pressure than the ambient air pressure. This is then used to boost the braking force when the brake pedal is pressed.

The servo unit contains to volume chambers which are both connected to the vacuum reservoir but separated by a diaphragm. The servo hydraulic piston is operated by fluid forced from the master cylinder but also by a spindle attached to the centre of the diaphragm.

At rest when no braking force is applied, there is no flow of hydraulic fluid and both chambers are at equal pressure and so no force is exerted on the piston.

However when the brake is applied, the master cylinder piston is pushed down the bore forcing fluid from the master cylinder to the servo unit. This operates the servo hydraulic plunger. Near the end of the travel of the master cylinder piston, it operates a reaction valve.

The reaction valve first disconnects the servo’s rear chamber from the vacuum supply and then opens the rear chamber to atmospheric pressure. This creates a pressure difference between the front and rear chambers, which forces the diaphragm and attached spindle forward. Thus increasing the force applied to the servo hydraulic piston.

Once these were installed on the car, it was time for the fabrication of the hydraulic piping ….

The brass fittings were salvaged from the Automec kit and the copper piping used for making mock-ups of the more complex sections. Cunifer piping is typically sold in 25 foot coils which was more than enough. So I had plenty spare ‘just in case’ I made a hash of making the individual pipes.

I now needed to straighten the replacement Cunifer piping and also to obtain a brake flaring tool. Initially I purchased a flarer from Machine Mart which was little short of useless and had the typical Made in China quality about it. I ought to know better by now!

There’s always a number of old, quality flaring tools on eBay but these usually change hands for well in excess of £100. I think people just resell them back on eBay once they’ve finished their restorations, which is what I planned to do. However after being outbid on numerous times I gave up as I needed to press on.

The Oakes brake flaring tool purchased from Automec was well worth the investmentAfter a recommendation, I picked up a new Oakes tool from Automec at the Jaguar Spares Day for a show price of £90. Quite a bit for a tool for a one off job but it does produce good, consistent flares every time. All in all, a good investment and a quality tool.

I’d previously straightened all the copper piping over a form (covered in a previous post) but subsequently disposed of the wooden form, thinking I’d no longer need it!

I did come across a straightening tool produced by a company called Kwix UK which seemed promising. However it only straightens a pipe of a fixed diameter so I’d need three tools for each of the pipe diameters used for the brake and fuel lines.

One to avoid - the Kwix UK pipe straightener - it could be a good product but really let down by their customer serviceThe 1/4″ brake pipes linking the master cylinder and servo run around the engine frames. I thought any slight bends/kinks in these pipes would be more noticeable as they run along the straight edges of the frames. The 1/4″ tool was purchased as a trial and it worked well so I got the 5/16″ one for the fuel lines.

Unfortunately this time, the pipe passed straight through without a hint of straightening and emails to the company received no response. I think they probably just sent the wrong sized tool but couldn’t be bothered with addressing customers’ issues so I won’t be dealing with them again!

The difficulty with bending the pipes was that often it wasn’t possible to trial fit the pipe after each bend was made. The unbent length would usually foul some part of the bodywork, stopping the pipe being placed in situ to mark the exact point for the next bend.

There was little margin for error for pipes that had to be bent in different planes. It only takes slight errors in the position of the bend, the angle of the bend or the plane in which the bend is made for it not to fit and the errors are magnified once another bend or two is added.

The clutch and rear brake piping, although the photos don't quite capture the various bends in numerous different planesThe mantra measure twice cut once applied here as, once bent, it’s almost impossible to re-straighten a pipe, especially the larger diameter piping. In fact it was more like measure 10 times, bend once! I probably had to discard just under half of my first attempts.

Having completed the hydraulics, I’m not convinced of the wisdom of purchasing kits as it would be nigh on impossible to get all the pipes right first time. So I’m glad I decided to fabricate my own pipes and it was quite therapeutic.

Having said that, I still managed a few numpty moments. A couple of times I allowed the brass fitting to slide away from the flared end onto the wrong side of where the bend was then made. Another scrapped length of piping!

The copper kit didn’t go completely to waste as it was cut down into shorter lengths and used to get correct position, angle and plane for a small section with say 2 or 3 bends. This could then be offered up without fouling the bodywork before making the same bends in the full length of pipe.

I had all but a few of the original pipes to use as templates however I did deviate in a couple of areas:

  • The pipe to the rear runs along the under floor box section but divert so it is clear of the mounting bolts for the torsion bar reaction plate. In doing so I think the pipe would be more exposed to damage. I continued running along the box section and will just need to take care when doing up the torsion plate bolts.
  • I thought it looked neater having straight piping around the front of the engine frames rather than trying to get them to mirror all the rises and falls in the frame profile. Therefore, just before the front brake union, the smaller front brake pipe jumps over the larger pipe rather than underneath.

Also my pipe bender couldn’t get as tight ‘U’ bends from the brake and clutch master cylinders and other methods were prone to causing the pipe to start collapsing.

Hydraulic Pipe Routing
Below are a few photos of the trial fitting of the various hydraulic pipes on the S2.

Clutch from Master Cylinder Clutch low pressure pipe

The routing of the clutch piping from the master cylinder to the flexible hose union. Note - not fitted at this stage is the P-clip on the LH frame bolt, securing the pipe

The clutch low pressure hose has a tight U-bend before running parallel with the engine frame

Brake – Master to Servo Brake – around Picture Frame Brake – Master to Servo & To Front

The brake pipe from the master cylinder to the servo unit also has an initial tight U-bend before running down the diagonal, round engine frame

The pipe then routes around the bottom of the picture frame to an inline union

From the union, the pipe travels up the opposite side frame member to the servo unit.

Front feed over Master to Servo Left Front Brake Righr Front Brake

The feed fro mthe servo to the front brakes first passes underneath the thicker master to servo pipe and then over it to the front union

The left brake pipe from the front union

The right brake pipe from the front union

Servo to Rear Union Union to Rear A few off cuts!!

The path of the pipe for the rear brakes from the servo to an inline union, which includes the brake light hydraulic switch

From the brake light switch union, the rear pipe passed down the LHS of the underside of the car

The fitting of the clutch and brake pipes was definitely a case of practice makes perfect - a few off cuts!

Jan 232013
 

The brake reservoir caps house electrical connections for the float operated switch for the brake fluid warning light and appeared to be quite corroded. It was only once they had been opened that it became clear that what I thought was corrosion was probably crystallised hydraulic fluid.

Both the reservoir caps appeared to be corroded but it was actually crystalised hydraulic fluid This was most of the contents of the first reservoir! The second reservoir was not much better!

The float should be enclosed in an aluminium cylinder but most of this had corroded away. I had little option but to replace the reservoirs which was a shame. Replacements are readily available however an alarming number of people had reported problems with them splitting and the resulting leak causing havoc with the paint work.

Reading other people’s woes with the repro products, I think the splitting might be initiated either when the black low pressure rubber tubing is pushed on, as a reasonable amount of force is required, or by over-tightening the hose clamps. Basically the new parts are not particularly good quality and no doubt originate from China.

The original bottles had a metal insert inside the supply protrusion/outlet which would avoid the over-tightening issue. The insert also had a gauze nylon filter, again missing from the new ones.

The clutch reservoir was better as the fluid hadn’t crystalised, which I’m now thinking might be caused as the aluminium float shroud corrodes. However there was a lot of gunk at the bottom so I thought it wise to replace as well.

Reservoir cut open to retrieve the metal insert

I decided to salvage the metal inserts by cutting the bottles in half. These were zinc-nickel plated along with the bracket clamps before being inserted into the new bottles. The method I use to insert them was to pass a piece of string through the supply outlet to act as a guide.

A rod was then used to carefully push the insert home while supporting the other side to minimise the stress on the plastic bottle. The reverse was done when pushing on the low pressure rubber tubing, opposing the pressure with the same rod. Hopefully it will be ok.

I couldn’t work out a method of refitting the nylon gauze filter on to the metal insert once it was in place. The filters were not in the best of shape so they have been omitted.

Brake and Clutch reservoirs reunited with re-plated bracket Brake Servo reservoir showing the aluminium shroud around the float

However this does lead on to my next dilemma. As the calipers have been reconditioned and the reservoirs and hydraulic pipes replaced, I have the opportunity to switch from DOT4 to silicone brake fluid.

I like the idea of using the silicone fluid to avoid potential future problems with leaks damaging the paint work, especially in light of the problems others have had with the new reservoir bottles. Conversely there are views that the rubber seals can be damaged over the long term by the silicone.

It seems there isn’t a general consensus on which is the best way to go and it’s difficult determining whether advice is based on fact or merely that the person went down that route themselves and therefore it must be the right choice! Hmmmmm ……